home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Shareware Overload Trio 2
/
Shareware Overload Trio Volume 2 (Chestnut CD-ROM).ISO
/
dir24
/
crcmfhg1.zip
/
MISC
/
FRAUD
/
ALLPHONE
/
A_VOX03.TXT
< prev
next >
Wrap
Text File
|
1993-04-17
|
4KB
|
110 lines
AUDIOVOX 3100A,4100A,SP85A,CMT410A,BC55A,CTR1900,PT 300/BC55A,CTR1900
NOTES: These are single NAM units that have user programmable MIN & SIDH,
See below for user instructions.
The ESN prefix is 138 decimal, 8A hex (Toshiba)
These units have an excessive number of "security" features,
You MUST know the lock code or the "reprograming" code and you
may also need an "activation" code. Take care not to program
these options unless you're sure the numbers will not be mislaid.
There is a "back door" for the PT 300 portable, see end.
Audiovox: 516-231-6051/310-926-7758
NAM programing:
1. With the power turned on enter N N N FUNC # 1, where NNN is the three
digit lock code. The manufacturers default is 000. If a reprograming
code has been entered in step 26 (see below) this code must be used in
place of the three digit lock code. If "CODE ?" appears when the phone
is powered up then you must enter the 7 digit "Activation Code" before
entering programing mode, (see step 30).
2. The # key increments the step number.
3. The * key decrements the step number.
4. STO enters the data for each step.
5. You MAY directly access any step by pressing RCL followed by the step
number.
6. FUNC SND completes programing.
7. FUNC CLR exits programing mode.
PROGRAMING DATA:
STEP# #OF DIGITS/RANGE DESCRIPTION
01 10 DIGITS MIN (AREA CODE & PHONE NUMBER)
02 3 DIGITS LOCK CODE
03 00000 - 32767 SYSTEM ID
04 00 - 15 ACCESS OVERLOAD CLASS
05 00 - 15 GROUP ID (10 FOR USA)
06 0 OR 1 LOCAL USE MARK
07 0 OR 1 MIN MARK
08 0333 OR 0334 INITIAL PAGING CHANNEL
09 0 OR 1 PREFERRED SYSTEM
10 4 DIGITS STATION CLASS MARK
11 8 BINARY DIGITS FUNCTION 1, SEE NOTE 1 BELOW
12 8 BINARY DIGITS FUNCTION 2, SEE NOTE 2 BELOW
13 00 TO 31 HOURS POWER OFF TIMER (CTX 4000 ONLY)
14 000 TO 255 SECS NO CHARGE AIR TIMER DELAY
15 3 DIGITS CALL TIMER RESET CODE
16 - 25 00000 - 99999 SIDH INHIBIT # 1 THRU # 5
26 3 DIGITS NAM PROGRAMING CODE (LEAVE BLANK, SEE ABOVE)
27 - 29 NOT USED FUTURE USE
30 7 DIGITS ACTIVATION CODE (LEAVE BLANK, SEE ABOVE)
NOTES:
1. This is an eight digit binary field.
10000000 = CALL TIMER BEEP
01000000 = AUTO LOCK
00100000 = AUTO SYSTEM REDIAL
00010000 = CALL RESTRICTION
00001000 = 32 DIGIT DIALING CAPABILITY
00000100 = AUTO ANSWER
00000010 = AUTO ANSWER FOR DATA
11111000 = ALL OF THE ABOVE
2. As above but options are:
10000000 = HANDS FREE
01000000 = CONTINUOUS DTMF
00100000 = REPERTORY DIALING
00010000 = HORN ALERT
00001000 = ALLOWS 911 CALLING WHEN UNIT IS LOCKED
01101000 = ALL OF THE ABOVE
A/B SYSTEM SELECT:
FCN 0 4 DISPLAYS CURRENT MODE,
FCN 0 0 = PREFERRED/NON-PREFERRED,
FCN 0 1 = PREFERRED ONLY,
FCN 0 2 = HOME ONLY
FCN 0 3 = NON PREFERRED ONLY,
USER PROGRAMING OF MIN & SIDH
Press CLR followed by the new five digit SIDH and ten digit MIN.
Press FUNC 6. The new MIN will be displayed, hold 6 to display the SIDH.
"BACK DOOR" FOR PT-300
1. Remove the battery.
2. Remove the small black square access plate at the lower left of the
phone.
3. Place a 10k resistor between pins 4 and 5.
(Pin 5 is top right, pin 4 is center bottom)
4. Replace battery, power up phone and enter 0 0 0 FUNC # 1.
LOCK: Press LOCK. UNLOCK: Enter three digit code.
SYSTEM SELECT: F 0 4 shows current mode. F 0 0 = Pref/Non pref, F 0 1 = Pref
only, F 0 2 = Home Only, F 0 3 = Non pref only.